-72 1641cc turbo build log

villemil · Post by **villemil** » Mon Apr 27, 2020 4:35 pm

Haha. Those were my winter tires

madmike · Post by **madmike** » Wed Apr 29, 2020 5:26 am

I thought so ,, they are 'Ban' here unless u deliver the 'Mail'

we had a 250r Honda 4 wheeler once with snowmobile 'drag picks' in the rear tires ,,
sure thew sparks on the pavement

villemil · Post by **villemil** » Sun May 24, 2020 8:18 am

Turbo ready for install. Next friday I will finally get my engine block and then I can start assembling. Car is almost ready otherwise.

madmike · Post by **madmike** » Mon May 25, 2020 4:10 am

Progress

panel · Post by **panel** » Mon May 25, 2020 10:46 am

Tell us more about your tablet set-up ?

villemil · Post by **villemil** » Mon May 25, 2020 1:15 pm

panel wrote: ↑Mon May 25, 2020 10:46 am Tell us more about your tablet set-up ?

I used double side tape to mount that and the gauges are for 123 Tune+ distributor. I can see ignition advance, rpm, boost pressure etc on the screen. Connected to the distributor with bluetooth. Also I can adjust my ignition map and rev limiter on the road

villemil · Post by **villemil** » Fri May 29, 2020 11:07 am

Engine block arrived today. Painted it and it's ready for assembling

buguy · Post by **buguy** » Fri May 29, 2020 5:39 pm

Ooooh. That's the fun part!

villemil · Post by **villemil** » Tue Jun 02, 2020 1:40 am

Engine ready to go in for a test fit and to make my exhaust and intake. Those heads are just for making my exhaust and intake piping. Still waiting for my heads that will go to my engine. Those will take around 3 weeks to get them from machining

villemil · Post by **villemil** » Wed Jun 03, 2020 4:08 am

Some planning. Turbo needs to sit a bit lower but otherwise looks good

madmike · Post by **madmike** » Wed Jun 03, 2020 5:00 am

Looking good , so what size valve ?heads?

villemil · Post by **villemil** » Wed Jun 03, 2020 6:22 am

madmike wrote: ↑Wed Jun 03, 2020 5:00 am Looking good , so what size valve ?heads?

I got ported stock 1600DP heads.

villemil · Post by **villemil** » Sat Jun 06, 2020 9:24 am

Drop spindles & ATS Classic wheels installed

buguy · Post by **buguy** » Sat Jun 06, 2020 9:46 am

Looks good. I like those.

Schweg · Post by **Schweg** » Sat Jun 06, 2020 10:08 am

Looks good.

Shoptalkforums.com

-72 1641cc turbo build log

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build

Re: My -72 street car turbo build