Kbwakesk8's cars ,i need help!

Skidmark · Post by **Skidmark** » Wed Jun 04, 2008 4:53 pm

The one I use is a Fuelsafe brand... p/n RS122A. They are more expensive, but you get what you pay for when it comes to fuel storage and safety. I built an aluminum enclosure for it, since the vehicle code (when did I ever pay any attention to THAT?!!) states the driver and passenger compartment must be separated from the fuel tank by a metal bulkhead.

KBWAKESK8 · Post by **KBWAKESK8** » Wed Jun 04, 2008 5:55 pm

I was looking at the fuel safe one's they make a buggy tank that fits over the hump.

KBWAKESK8 · Post by **KBWAKESK8** » Mon Jun 23, 2008 9:44 am

MOTOR IS IN THE CAR.

now it s time for the plumbing.

still need to figure out where i want the gas tank and radiator

Post by **Hedrock** » Mon Jun 23, 2008 7:32 pm

your car looks awesome. The rear arms and new power made a huge difference. What is the yellow lite on the roof for?

Post by **Leatherneck** » Mon Jun 23, 2008 7:50 pm

Daaaaammmmmnnnnnnnn that looks nice!

KBWAKESK8 · Post by **KBWAKESK8** » Tue Jun 24, 2008 9:25 am

Leatherneck wrote:Daaaaammmmmnnnnnnnn that looks nice!

thanks

Hedrock wrote:your car looks awesome. The rear arms and new power made a huge difference. What is the yellow lite on the roof for?

the yellow light my freind foud it and stuck it on my car just never pulled it off

the car is starting to look more balanced. Im tring to figure out where to put the gas tank ,radiator ,and spare tire.

npetric · Post by **npetric** » Fri Jul 11, 2008 7:40 am

KB sent you a pm to see how wide your back is after your new arms.

Your rides lookin sweet

KBWAKESK8 · Post by **KBWAKESK8** » Thu Jul 17, 2008 11:07 am

npetric Your a arms look sick makes me wish i went that direction.

So i started the rear engine cage not sure about it yet.

Im allso building a new intake.

npetric · Post by **npetric** » Thu Jul 17, 2008 12:26 pm

I like the rear cage alot so far......Why ya gonna build a new intake? That one thats on there is sweet!!

KBWAKESK8 · Post by **KBWAKESK8** » Thu Jul 17, 2008 1:16 pm

npetric wrote: I like the rear cage alot so far......Why ya gonna build a new intake? That one thats on there is sweet!!

The air cleaners get dirty real quick. they pick up dust created by the back tires right there. the new one is going to hold the air cleaners up by the rear windo its going to look sick.

npetric · Post by **npetric** » Thu Jul 17, 2008 1:31 pm

You cutting up the old one? Or sending it my way

KBWAKESK8 · Post by **KBWAKESK8** » Thu Jul 17, 2008 1:42 pm

npetric wrote:You cutting up the old one? Or sending it my way

I have not cut up the old one. I could send it your way.

npetric · Post by **npetric** » Thu Jul 17, 2008 2:15 pm

That would be awesome
pm sent

Skidmark · Post by **Skidmark** » Thu Jul 17, 2008 5:27 pm

I would think about not having the lower horizontal part of your bumper loop right where the exhaust gasses flow - it looks like the exhaust flow would be split over both sides of that tube. I love the look of that exhaust! Maybe have that part of the cage above the exhaust baffles... just my $.02

KBWAKESK8 · Post by **KBWAKESK8** » Thu Jul 17, 2008 5:31 pm

Skidmark wrote:I would think about not having the lower horizontal part of your bumper loop right where the exhaust gasses flow - it looks like the exhaust flow would be split over both sides of that tube. I love the look of that exhaust! Maybe have that part of the cage above the exhaust baffles... just my $.02

It actually is just a bad angle i will take more of a side pic.