Project---Split cable pull linkage

slowtwitch · Post by **slowtwitch** » Wed Nov 17, 2010 5:35 am

Just want to say thanks to all that have inquired about the system and to apologize to some for being a little late in getting back to you. i've been kinda sidelined working on this.....

My new 30'x32' garage

Stufenheck · Post by **Stufenheck** » Wed Nov 17, 2010 7:52 am

Pete,

That's a very nice garage.

Jesse

Ephry73 · Post by **Ephry73** » Wed Nov 17, 2010 9:09 am

I have died and gone to heaven! Geezus this works out just like the one I designed, but a million times better. Solves a lot of issues. Are these still available?

E

Post by **Piledriver** » Sun Nov 21, 2010 1:49 pm

Groovy...

I bet there's room for a mill AND a lathe in that

slowtwitch · Post by **slowtwitch** » Tue Nov 23, 2010 3:47 pm

I've been published....kinda of

I did a linkage setup for Jason's Ghia awhile back...

He just notified me that he made the front cover of January, 2011 Hot VW's. He also told me that there is a good shot of the system in the article.

Here's the preview...

http://www.hotvws.com/issue_preview.html

Post by **Piledriver** » Tue Nov 23, 2010 4:09 pm

You had better get to work installing that machine shop...

trapnm · Post by **trapnm** » Wed Nov 24, 2010 7:06 pm

Pete,
Congratulations on being posted in the article. I wish they would have mentioned your set up in the narrative, but a pic and caption is pretty great. The only issue I see in the pic, is that the height of the cable in the bracket doesn't line up with the top of the pulley wheel as I have seen on your other set ups, and on the one I helped install. Do you know if this an installer mod due to some other issues with the turbo engine?

slowtwitch · Post by **slowtwitch** » Wed Nov 24, 2010 11:28 pm

trapnm wrote:Pete,
The only issue I see in the pic, is that the height of the cable in the bracket doesn't line up with the top of the pulley wheel as I have seen on your other set ups, and on the one I helped install. Do you know if this an installer mod due to some other issues with the turbo engine?

That was an early prototype. It was also the first throttle body setup and we didn't have much time to make adjustments.

geniusanthony · Post by **geniusanthony** » Wed Dec 15, 2010 10:50 pm

Pete, I am interested in one of your linkages. If any are available please advise.
/Tony

yetibone · Post by **yetibone** » Sat Jan 01, 2011 3:17 pm

I installed mine last week, and it's a night-and-day difference over the hex-bar. So much easier throttle actuation, and way better accuracy. My carbs stay in sync now no matter how many times I go full throttle.

Thanks Pete, and happy new year.

RonW · Post by **RonW** » Sat Jan 01, 2011 7:24 pm

pete,
just got my motor back up and running now with LS2 COP and setting up for sequential spark and squirt. you have then ready for the Jenvey ITBs yet?!?!

happy new year
ron

slowtwitch · Post by **slowtwitch** » Sun Jan 02, 2011 6:06 am

RonW wrote:pete,
just got my motor back up and running now with LS2 COP and setting up for sequential spark and squirt. you have then ready for the Jenvey ITBs yet?!?!

happy new year
ron

Ron, I have the drawings done, but, I'm currently in the process of locating a CNC mill and lathe. Doing it manually has it's restrictions

Wally · Post by **Wally** » Sun Jan 02, 2011 9:41 am

slowtwitch wrote:
RonW wrote:pete,
just got my motor back up and running now with LS2 COP and setting up for sequential spark and squirt. you have then ready for the Jenvey ITBs yet?!?!

happy new year
ron
Ron, I have the drawings done, but, I'm currently in the process of locating a CNC mill and lathe. Doing it manually has it's restrictions

Good question!

as I also run a set of Jenvey's

and still would like to run a set.
You may go first Ron, I'll have version 2.0 then

PS interesting to learn your running COP now with chevy parts. Any link to your build? (might have missed it?)
Tnx.

RonW · Post by **RonW** » Sun Jan 02, 2011 3:13 pm

Wally wrote:
slowtwitch wrote:
RonW wrote:pete,
just got my motor back up and running now with LS2 COP and setting up for sequential spark and squirt. you have then ready for the Jenvey ITBs yet?!?!

happy new year
ron
Ron, I have the drawings done, but, I'm currently in the process of locating a CNC mill and lathe. Doing it manually has it's restrictions
Good question! as I also run a set of Jenvey's
and still would like to run a set.
You may go first Ron, I'll have version 2.0 then

PS interesting to learn your running COP now with chevy parts. Any link to your build? (might have missed it?)
Tnx.

Wally,
No real build thread but started posting in the FI forum since i was having some issues bench testing. the thread has morphed to a build thread now...kinda.

http://shoptalkforums.com/viewtopic.php?f=23&t=134054 (sorry for the brief hijack)

I had shipped Pete my bodies earlier to take measurements so us Jenvey folks could feel the love too.

Cant wait to check them out

ron

nikojo · Post by **nikojo** » Sun Feb 20, 2011 7:58 am

Hi everyone,

Looking for information on where to order the kit??

I've PM'ed Pete so hopefully that is it, but was wondering if there is another way people have been doing this??

Thanks.

JJ

Shoptalkforums.com

Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage

Re: Project---Split cable pull linkage