CB Performance Uni -Tech rods

Post by **sparkmaster1** » Fri Jul 05, 2002 9:26 pm

Has anyone seen or used these?
UNI-TECH Performance Connecting Rods. They look kind of like the Scat I beam rods with a CB on the side. They are advertised on the CB website. For $97.95 they don't look too bad. Tim

stkrmtr · Post by **stkrmtr** » Sun Jul 07, 2002 2:40 pm

Bought mine and we have a machine shop on site and I handed a stock rod and a uni-t and then gave him vw's spec.s. He check them for straightness....so-on. They look great for the price. I will be assembling the motor next week so I'll let everyone know how it goes-SS

[This message has been edited by stkrmtr (edited 10-04-2002).]

McBernie · Post by **McBernie** » Sun Jul 07, 2002 2:48 pm

I think what Dallas was trying to say was that they are pretty good rods-I built a 2007cc motor with these rods,they are well balanced and the case needs very little clearancing.If your going over 7000rpm on a regular basis then I'd go with the CB Super race rods H beams with 2000 bolts

vw1303sb · Post by **vw1303sb** » Sun Jul 07, 2002 2:50 pm

Hey what do ya know I am moving to dalls at the end of this month

McBernie · Post by **McBernie** » Mon Jul 08, 2002 2:55 am

Unlucky !!!! LOL

ANT · Post by **ANT** » Mon Jul 08, 2002 8:35 am

<BLOCKQUOTE>quote:<HR>Originally posted by stkrmtr:
Bought mine and we have a machine shop on facility and took tho specs of what they should. Thaey buid big block and spendd$$$$$ they called BS on me when I tolld the th price-gimme a fek and I'll tell yah for sure (MY NNNAAASSS mMOTOR DOG-yo<HR></BLOCKQUOTE>

Exsqueeze me, but what the FOCK are you talking about? Try to use the King's English. I can't make heads of tails out of your fractured and ignorant attempt at Ebonics. Grow the hell up.
-ANT

Post by **Marc** » Mon Jul 08, 2002 8:49 am

<BLOCKQUOTE>quote:<HR>Originally posted by ANT:
 ...Try to use the King's English. I can't make heads of tails out of...
-ANT<HR></BLOCKQUOTE>

Thanks ANT, someone had to say it. Even my 16-year-old was unable to translate for me.
(World's worst job? Proofreader for a rap magazine)

Stripped66 · Post by **Stripped66** » Mon Jul 08, 2002 9:16 am

<BLOCKQUOTE>quote:<HR>Originally posted by Marc:
 Thanks ANT, someone had to say it. Even my 16-year-old was unable to translate for me.
(World's worst job? Proofreader for a rap magazine)<HR></BLOCKQUOTE>

Skizzy fo-shizzy Biatch!!!

stkrmtr · Post by **stkrmtr** » Mon Jul 08, 2002 3:58 pm

sorry for all the missellins-rolled a car a few time-sever cocusion-14 spaples holding my head toghter -doc said I preobablly won'tr be right for a few month-ss-Not all Dallasitse are tards -=-check out www.aircooledpart.com -- we took out product cause they kept on gutting coppied-newest is super duty 2 pieci indestrutable clutch tube w/braces and super duty gasket kit

Fig · Post by **Fig** » Mon Jul 08, 2002 5:13 pm

[QUOTE]Originally posted by stkrmtr:
....Not all Dallasitse are tards...

Hmmmm, are you a ... Rock with lips?

Post by **Piledriver** » Mon Jul 08, 2002 6:20 pm

I think stkrmtr had an accident and is temporarily handicapped.

Give him a little break, there is no spell checker...

Post by **sparkmaster1** » Mon Jul 08, 2002 7:16 pm

So back to the original post. Has anyone else tried these rods? I have two 2110's to do next and they look pretty good to me. How about Scat's I beam rods? Any good/bad reports on those? I usually use stock clearanced rods but with the price of cores these days, new looks like about the same price. Tim

ANT · Post by **ANT** » Tue Jul 09, 2002 9:23 am

<BLOCKQUOTE>quote:<HR>Originally posted by sparkmaster1:
So back to the original post. Has anyone else tried these rods? I have two 2110's to do next and they look pretty good to me. How about Scat's I beam rods? Any good/bad reports on those? I usually use stock clearanced rods but with the price of cores these days, new looks like about the same price. Tim<HR></BLOCKQUOTE>

How dare you attempt to get back on topic!! Have you a concussion too? LOL

Could you post a link to those rods? I'm using a set of those Scat rods for my 1914--Kustom 1 Warehouse sells them for $120 a set. I wonder how they compare to each other.
-ANT

Post by **sparkmaster1** » Tue Jul 09, 2002 7:45 pm

Here's the link. http://www.cbperformance.com/catalog.asp?ProductID=1179

I wonder where they are made. Tim

effvee · Post by **effvee** » Tue Jul 09, 2002 8:23 pm

Wow they look just like the Scats I have without the ARP bolts. Look like a toss up.