I think the fk10 is somewhere between the 86b and the 86c.
Mine came in big..270 at .050
Yes fuel.
I have 320cc
the itbs have 44mm butterflies. But the throat under is 43mm
New Start Up 2387
-
- Posts: 2433
- Joined: Wed Apr 13, 2011 1:01 pm
Re: New Start Up 2387
have you got your req fuel setup in the settings?
mine are gsxr 750 itbs so a bit smaller and if i recall 240cc injectors. i'll dig out a fuel map but it'll be no help to you as your injectors are bigger i think..
mine are gsxr 750 itbs so a bit smaller and if i recall 240cc injectors. i'll dig out a fuel map but it'll be no help to you as your injectors are bigger i think..
-
- Posts: 195
- Joined: Mon Feb 09, 2015 4:45 am
Re: New Start Up 2387
I understand that it will not be for my engine at all.
I am looking more for the general shape of what an itb on alpha looks like.
Even a screen shot of the 3d view of table would be a great help.
I am looking more for the general shape of what an itb on alpha looks like.
Even a screen shot of the 3d view of table would be a great help.
-
- Posts: 2433
- Joined: Wed Apr 13, 2011 1:01 pm
Re: New Start Up 2387
Alpha n (TPS) or speed density (map) ?
Yep I'm with you let me know and I'll dig one out
Yep I'm with you let me know and I'll dig one out
-
- Posts: 195
- Joined: Mon Feb 09, 2015 4:45 am
Re: New Start Up 2387
My numbers in the cells will be different but the general "shape" would be simular I am guessing.
Yes straight alpha n on itb.
Yes I do have the req fuel and constants set up.
That was a cluster with the dual table set up.
I had read somewhere that the fuel and constants were set to only what is actually on that table.
Dual table, engine split in two banks. One table with its constants for bank 1. The other table with its constants set for bank 2.
Intitial testing seems that even though each table only has two cylinders on it, the constants have to be set to total cylinders and injectors. That is for bank one and bank two.
So anyhow......
Mine is split header, 2 bank, 2 o2, 2 fuel table. Single ignition table.
1 and 3 paired up header, injectors, table.
then 2 and 4 paired up.
Not table switch but simultaneous 2 table.
Yes straight alpha n on itb.
Yes I do have the req fuel and constants set up.
That was a cluster with the dual table set up.
I had read somewhere that the fuel and constants were set to only what is actually on that table.
Dual table, engine split in two banks. One table with its constants for bank 1. The other table with its constants set for bank 2.
Intitial testing seems that even though each table only has two cylinders on it, the constants have to be set to total cylinders and injectors. That is for bank one and bank two.
So anyhow......
Mine is split header, 2 bank, 2 o2, 2 fuel table. Single ignition table.
1 and 3 paired up header, injectors, table.
then 2 and 4 paired up.
Not table switch but simultaneous 2 table.
-
- Posts: 2433
- Joined: Wed Apr 13, 2011 1:01 pm
-
- Posts: 195
- Joined: Mon Feb 09, 2015 4:45 am
Re: New Start Up 2387
Well mine looks awful big...
But the shape is similar i guess.
I will get to spend more time with it another day.
Thanks.
But the shape is similar i guess.
I will get to spend more time with it another day.
Thanks.
- Piledriver
- Moderator
- Posts: 22520
- Joined: Sat Feb 16, 2002 12:01 am
Re: New Start Up 2387
Note the max value in those tables is (technically) 255, so as long as you keep it not much over 200, you can get some more low end resolution by reducing the reqfuel and multiplying the VE table the same %.
(You have to leave a little headroom for WUE etc, the total calc value cannot exceed 255, max just under 200 in ve table probably safe)
On MS2e/MS3 max value is an unsigned 16bit number IIRC, which would be ridiculous to actually use, but nothings going to push that and make it barf on it. MS3 has an extra decimal place, so its particularly heavy overkill.
(You have to leave a little headroom for WUE etc, the total calc value cannot exceed 255, max just under 200 in ve table probably safe)
On MS2e/MS3 max value is an unsigned 16bit number IIRC, which would be ridiculous to actually use, but nothings going to push that and make it barf on it. MS3 has an extra decimal place, so its particularly heavy overkill.
Addendum to Newtons first law:
zero vehicles on jackstands, square gets a fresh 090 and 1911, cabby gets a blower.
EZ3.6 Vanagon after that.(mounted, needs everything finished) then Creamsicle.
zero vehicles on jackstands, square gets a fresh 090 and 1911, cabby gets a blower.
EZ3.6 Vanagon after that.(mounted, needs everything finished) then Creamsicle.