SOLD CNC Hubs for Combo Spindles

Bajas, Rails and Parts

Moderator: Leatherneck

Post Reply
User avatar
DeMinimis
Posts: 1547
Joined: Wed Nov 09, 2005 11:05 pm

SOLD CNC Hubs for Combo Spindles

Post by DeMinimis » Tue Feb 09, 2016 12:04 am

Prototype /one-off hubs. These are true knock-offs (gave away the plates and knock-off spinner when I sold the rears years ago). Very beefy. Remove pins (allen screws), drill and press in studs. Rotors heavily pitted, but you could probably clean them up and use them (or replace with new ones @ $89.99 ea from Jimco). These were never used! Dusty. Comes with new in the boxes Timken bearings and races, along with SKF seals ($150+ from Pacific Customs). Bummed I can use them (new ride has KK spindles). $275 shipped to west coast-ish. Thanks.

Image

Image

Image
Last edited by DeMinimis on Fri Feb 12, 2016 11:06 am, edited 1 time in total.

User avatar
DeMinimis
Posts: 1547
Joined: Wed Nov 09, 2005 11:05 pm

Re: CNC Hubs for Combo Spindles

Post by DeMinimis » Tue Feb 09, 2016 8:21 pm

Comes with new studs/Lugs in package. Drill with 9/16 bit (37/64 is ideal), you've already got good sized pilot holes, press in and that's that. This is a fraction of what it cost for new CNCs.

User avatar
BAJA-IT
Posts: 1984
Joined: Tue Oct 07, 2008 7:02 pm
Location: Centerville, UT

Re: CNC Hubs for Combo Spindles

Post by BAJA-IT » Wed Feb 10, 2016 6:36 pm

These are so tempting!
BRAT Motorsports #936
Bolt Center: Salt Lake City, Ut
ACE: Air Cooled Engineering, now Black Line Racing

User avatar
DeMinimis
Posts: 1547
Joined: Wed Nov 09, 2005 11:05 pm

Re: CNC Hubs for Combo Spindles

Post by DeMinimis » Wed Feb 10, 2016 6:46 pm

I can't believe they are still available after two days. Damn CNC hubs for combos run around $1k and these are even beefier than the current offerings.

1966bajabug
Posts: 507
Joined: Fri Sep 12, 2008 1:57 am
Location: Current resident of "Master" BAJA-IT'S household (aka Centerville, Utah)

Re: CNC Hubs for Combo Spindles

Post by 1966bajabug » Wed Feb 10, 2016 8:03 pm

I'll take them! PM sent!

User avatar
DeMinimis
Posts: 1547
Joined: Wed Nov 09, 2005 11:05 pm

Re: CNC Hubs for Combo Spindles

Post by DeMinimis » Wed Feb 10, 2016 8:20 pm

Well played sir... We'll played.

User avatar
DeMinimis
Posts: 1547
Joined: Wed Nov 09, 2005 11:05 pm

Re: CNC Hubs for Combo Spindles

Post by DeMinimis » Wed Feb 10, 2016 11:33 pm

Sold.

User avatar
BAJA-IT
Posts: 1984
Joined: Tue Oct 07, 2008 7:02 pm
Location: Centerville, UT

Re: SOLD CNC Hubs for Combo Spindles

Post by BAJA-IT » Wed Feb 17, 2016 6:22 pm

The parts came in yesterday, better than advertised.
Thanx again for the great deal.
BRAT Motorsports #936
Bolt Center: Salt Lake City, Ut
ACE: Air Cooled Engineering, now Black Line Racing

User avatar
DeMinimis
Posts: 1547
Joined: Wed Nov 09, 2005 11:05 pm

Re: SOLD CNC Hubs for Combo Spindles

Post by DeMinimis » Wed Feb 17, 2016 6:24 pm

No problem. Glad you like them. Always want folks to be pleasantly surprised (except Baja Herbie).

Post Reply