Dual Weber 44's setup and alot of 2.0L engine parts for sale

jmgeoff1 · Post by **jmgeoff1** » Sun Jan 08, 2006 10:46 am

I have a pair of weber 44idf's for sale, they come with intake manifolds for a 2.0L, air cleaners, hex bar linkage, a "How to tune webers" book and anything else carb related that I have. I'm looking to get $500. for the whole setup. I also have alot of 2.0L engine parts for sale. I'm putting a Ford 2.3L in my Riveria, so I have no need for my VW motor. The only thing that is broken from the engine is the crank and a head. I'm not trying the get rich from this stuff, just trying to get rid of it, so make me a resonable offer. Buyer will pay shipping unless otherwise agreed upon.

Geoff
[email protected]

R2.0 · Post by **R2.0** » Sun Jan 08, 2006 12:46 pm

Location? I assume from your email address it's North Carolina.

And when yoyu say "broken", does that mean "damaged" or "in more pieces than originally"?

jmgeoff1 · Post by **jmgeoff1** » Sun Jan 08, 2006 2:33 pm

I'm in Fayetteville/Ft.Bragg, NC. If you want the carbs I'll pay the shipping.
Geoff

jmgeoff1 · Post by **jmgeoff1** » Sun Jan 08, 2006 2:34 pm

The Crank is in two pieces, thats what I mean by broken, and the head has a spot that melted away. I can send pics if you want.

914pwr · Post by **914pwr** » Sun Jan 08, 2006 4:29 pm

How much for the carbs

jmgeoff1 · Post by **jmgeoff1** » Sun Jan 08, 2006 5:40 pm

Just the carbs?

jmgeoff1 · Post by **jmgeoff1** » Sun Jan 08, 2006 5:40 pm

$400. for just the carbs.

Guest · Post by **Guest** » Wed Jan 18, 2006 10:45 am

do you still have the carbs?

jmgeoff1 · Post by **jmgeoff1** » Wed Jan 18, 2006 2:13 pm

I have one left. Its probally going on ebay, unless you want it. I do have all the other stuff though. linkage manifolds air cleaners other carb related stuff

Post by **Daniel G** » Wed Jan 18, 2006 2:48 pm

How much for just the fan hub, bolt, and washer from the crankshaft? Also, was this a hydro lifter engine?

Daniel

jmgeoff1 · Post by **jmgeoff1** » Wed Jan 18, 2006 4:27 pm

I'll have to look for the fan stuff but I should have it. email me [email protected] Are you still looking for the carb stuff? Email me I check it more often.

jmgeoff1 · Post by **jmgeoff1** » Wed Jan 18, 2006 4:28 pm

it was a hyd lifter engine

manx96 · Post by **manx96** » Mon Jan 23, 2006 9:23 am

How much for the one carb, the linkage, manifolds, and the left over carb parts. I need them to finish my bus engine.

Manx96

jmgeoff1 · Post by **jmgeoff1** » Mon Jan 23, 2006 2:38 pm

The carbs are sold, but I have the intake manifolds, hex bar lin.kage, and the air cleaners. $75 bucks and you can have it all, I'll even throw in a "How to tune Webers" book, if your going to still put webers on it.

manx96 · Post by **manx96** » Mon Jan 23, 2006 5:25 pm

I will take all those parts so long the linkage is not worn out or the filters have holes in them. I pm'ed you.

Manx96