Erics 68 Squareback
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
Erics 68 Squareback
It will take me awhile to go through photobucket and find all the pictures of my Square, but here goes...
Recent pic
The air suspension
Recent pic
The air suspension
- supaninja
- Posts: 1658
- Joined: Tue Sep 14, 2010 12:48 pm
Re: Erics 68 Squareback
Here's one I took at a recent show
'65 notch w/ a squirted type 4
http://supaninjanick.wordpress.com/
'68 "Zombie Response Vehicle" Westy
viewtopic.php?f=14&t=140387
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
Re: Erics 68 Squareback
The front beam was narrowed four inches. Custom 4140 axles were machined to replace the torsions. Bronze bushings and housings were machined for the axles to ride smoothly inside the beam. I removed and retained the outer needle bearings for the control arms. The bulk head was relocated 2" higher and 2" narrower on each side. Custom bag brackets with 1.75" tubing and hiem ends bolt to boxed levers the rotate the axles to raise and lower the car. The bags are tucked away under the area the spare tire used to be located, and a bead rolled sheet metal cover hides them and the solinoids, wires, etc. A custom steering shaft was turned to fit the T3 steering box. Flaming River U-joints were installed to connect the box to the shaft. Everything was then torn down, cleaned, bead blasted, and painted Base/Clear.
The Paint gun is a bleed-off that will lower the car after turning a ball valve to locate air to the trigger!!
More Later
The Paint gun is a bleed-off that will lower the car after turning a ball valve to locate air to the trigger!!
More Later
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
Re: Erics 68 Squareback
Custom removable dash. Fabbed from 18 gage steel.
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
Re: Erics 68 Squareback
A 1915 powers it. CB 044 heads 94mm p/c's. Berg counter wieghted crank. Engle 120 cam, 1.25 rockers, chromoly push rods, 8.5 compression. Italian 44mm Webbers T1 intakes, custom full flow with recessed fan shroud, all AN fittings with braided SS line. External oil cooler Kymco 1 5/8 merged headers with a custom stainless Magnaflow set up.
Noisey straight cut cam gears
Noisey straight cut cam gears
Last edited by Eanderson on Mon Jun 13, 2011 10:49 pm, edited 1 time in total.
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
Re: Erics 68 Squareback
Kymco merged header
Magnaflow with custom SS up and over
Magnaflow with custom SS up and over
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
- Munchhausen
- Posts: 175
- Joined: Mon Feb 21, 2011 10:37 am
Re: Erics 68 Squareback
Lunatics with the right tools and to much time
Great car! I love it!
munch
Great car! I love it!
munch
- ALYKAT III
- Posts: 312
- Joined: Sat Apr 18, 2009 7:42 am
Re: Erics 68 Squareback
Beautiful ride ! Has to be one of my all time favorite T3s.
-
- Posts: 6
- Joined: Tue Mar 23, 2010 8:09 am
Re: Erics 68 Squareback
The dude has skills!!!!!!!!!!!
- Eanderson
- Posts: 17
- Joined: Wed Jun 08, 2011 4:44 pm
Re: Erics 68 Squareback
Thanks guys I'm glad Ninja told me about STF! Thanks bro! There are some warriors around here I'm liking it!