My Megasquirt build, Volksbugly
- volksbugly
- Posts: 634
- Joined: Thu Sep 16, 2010 5:09 am
My Megasquirt build, Volksbugly
This came in the mail today.
https://picasaweb.google.com/1078300117 ... directlink
Already purchased:
Already installed my LC-1 from innovate (its how I tunned my carb)
http://www.innovatemotorsports.com/xcar ... 262&page=1
Fuel system (return line, pump, filter, regulator) - from Mario
Trigger Wheel - from Mario
sensors - from Mario (CLT, IAT)
http://www.thedubshop.net/
LS2 coils from website -I'll update later with link if anybody wants.
http://www.rrrdynotuning.com/store/#ecw ... uct=548968
CB Performance 40mm F.I. throttle bodies
http://www.cbperformance.com
a custom built wiring harness from Mario.
Injector Dynamics 725cc
I plan to install the Trigger wheel within the next two weeks,
and Install the Fuel system, fuel pump, regulator, filter, return line but not the throttle bodies within the next two weeks,
then get the ECU position sorted.
This is my daily driver, so I do a little each weekend.
https://picasaweb.google.com/1078300117 ... directlink
Already purchased:
Already installed my LC-1 from innovate (its how I tunned my carb)
http://www.innovatemotorsports.com/xcar ... 262&page=1
Fuel system (return line, pump, filter, regulator) - from Mario
Trigger Wheel - from Mario
sensors - from Mario (CLT, IAT)
http://www.thedubshop.net/
LS2 coils from website -I'll update later with link if anybody wants.
http://www.rrrdynotuning.com/store/#ecw ... uct=548968
CB Performance 40mm F.I. throttle bodies
http://www.cbperformance.com
a custom built wiring harness from Mario.
Injector Dynamics 725cc
I plan to install the Trigger wheel within the next two weeks,
and Install the Fuel system, fuel pump, regulator, filter, return line but not the throttle bodies within the next two weeks,
then get the ECU position sorted.
This is my daily driver, so I do a little each weekend.
Last edited by volksbugly on Fri Dec 29, 2017 3:57 pm, edited 6 times in total.
- Max Welton
- Posts: 3023
- Joined: Mon Jun 03, 2002 12:01 am
Re: My Megasquirt build, Stockish 1600
You'll need a 3-wire TPS. Or did the throttle-bodies come with one?
Max
Max
- supaninja
- Posts: 1658
- Joined: Tue Sep 14, 2010 12:48 pm
Re: My Megasquirt build, Stockish 1600
Sounds like a solid setup, MS3?
'65 notch w/ a squirted type 4
http://supaninjanick.wordpress.com/
'68 "Zombie Response Vehicle" Westy
viewtopic.php?f=14&t=140387
- volksbugly
- Posts: 634
- Joined: Thu Sep 16, 2010 5:09 am
Re: My Megasquirt build, Stockish 1600
@Max The throttle bodies came with a tps, its a 3 wire.
http://www.cbperformance.com/catalog.asp?ProductID=319
@Supaninja
Thanks! yeah is a MS3
future upgrades after I get it tuned and learn how to tune:
oil cooler
Turbo
ID cc1000 injectors
cry02 fuel cooler
water to air intercooler
78.4 x 92mm engine -with all the goodies... (this is a long term build though)
http://www.cbperformance.com/catalog.asp?ProductID=319
@Supaninja
Thanks! yeah is a MS3
future upgrades after I get it tuned and learn how to tune:
oil cooler
Turbo
ID cc1000 injectors
cry02 fuel cooler
water to air intercooler
78.4 x 92mm engine -with all the goodies... (this is a long term build though)
- Max Welton
- Posts: 3023
- Joined: Mon Jun 03, 2002 12:01 am
Re: My Megasquirt build, Stockish 1600
Very interesting. The separate page for the 48mm TBs says the TPS must be ordered separately.
http://www.cbperformance.com/catalog.asp?ProductID=412
I'm cogitating on a FI 2110 for my KG, not sure the 40s will flow enough.
I'm really hoping you go first to find that out!
Max
http://www.cbperformance.com/catalog.asp?ProductID=412
I'm cogitating on a FI 2110 for my KG, not sure the 40s will flow enough.
I'm really hoping you go first to find that out!
Max
- volksbugly
- Posts: 634
- Joined: Thu Sep 16, 2010 5:09 am
Re: My Megasquirt build, Stockish 1600
Ron (porche megasquirter here) was / is running jevee 43mm on a I think 2184... or something of the likes...
Its the hardest pulling NA car I have ever been in.
I personally think you will LOVE 40 mm,
Its the hardest pulling NA car I have ever been in.
I personally think you will LOVE 40 mm,
- Vee Dub Nut
- Posts: 1152
- Joined: Sat Mar 23, 2002 12:01 am
Re: My Megasquirt build, Stockish 1600
Looks good! Make sure to keep posting pics and updates.
- supaninja
- Posts: 1658
- Joined: Tue Sep 14, 2010 12:48 pm
Re: My Megasquirt build, Stockish 1600
40's are more then enough for a 2110 Max, your still stuck in that carb mentality . 44IDF's only have 36mm venturi's.Max Welton wrote:Very interesting. The separate page for the 48mm TBs says the TPS must be ordered separately.
http://www.cbperformance.com/catalog.asp?ProductID=412
I'm cogitating on a FI 2110 for my KG, not sure the 40s will flow enough.
I'm really hoping you go first to find that out!
Max
'65 notch w/ a squirted type 4
http://supaninjanick.wordpress.com/
'68 "Zombie Response Vehicle" Westy
viewtopic.php?f=14&t=140387
- volksbugly
- Posts: 634
- Joined: Thu Sep 16, 2010 5:09 am
Re: My Megasquirt build, Stockish 1600
Oh btw, mine didn't come with the TPS, I had to buy all the extra hardware.
all said and done, I have about 800$ in the throttle bodies, fuel rails, fuel rail holders, tps, linkage hiem joints, and some air cleaner covers (mine were missing)
all said and done, I have about 800$ in the throttle bodies, fuel rails, fuel rail holders, tps, linkage hiem joints, and some air cleaner covers (mine were missing)
- volksbugly
- Posts: 634
- Joined: Thu Sep 16, 2010 5:09 am
Re: My Megasquirt build, Stockish 1600
So a quick update:
Had a little vacation,
car is in the shop currently getting 2nd gear repaired.. its warranty work. I'm looking for some fuel line clips. I plan to mount the lines under the body. I think I will go ahead and run two lines, one as a backup. I put out everything in the living room floor. I'll take some pics later tonight when I get home. I got the new pully installed, but can't find the bracket and hall sensor... Time to tear apart the office... (dont have a garage).
Pictures of the goodies soon.
Had a little vacation,
car is in the shop currently getting 2nd gear repaired.. its warranty work. I'm looking for some fuel line clips. I plan to mount the lines under the body. I think I will go ahead and run two lines, one as a backup. I put out everything in the living room floor. I'll take some pics later tonight when I get home. I got the new pully installed, but can't find the bracket and hall sensor... Time to tear apart the office... (dont have a garage).
Pictures of the goodies soon.
- supaninja
- Posts: 1658
- Joined: Tue Sep 14, 2010 12:48 pm
Re: My Megasquirt build, Stockish 1600
volksbugly wrote:Oh btw, mine didn't come with the TPS, I had to buy all the extra hardware.
all said and done, I have about 800$ in the throttle bodies, fuel rails, fuel rail holders, tps, linkage hiem joints, and some air cleaner covers (mine were missing)
I won't tell you how much my ITB's costed me but it was a lot less.
'65 notch w/ a squirted type 4
http://supaninjanick.wordpress.com/
'68 "Zombie Response Vehicle" Westy
viewtopic.php?f=14&t=140387
- Dale M.
- Posts: 1673
- Joined: Mon Oct 05, 2009 8:09 am
Re: My Megasquirt build, Stockish 1600
Tubing clips/clampsvolksbugly wrote:So a quick update:
Had a little vacation,
car is in the shop currently getting 2nd gear repaired.. its warranty work. I'm looking for some fuel line clips. I plan to mount the lines under the body. I think I will go ahead and run two lines, one as a backup. I put out everything in the living room floor. I'll take some pics later tonight when I get home. I got the new pully installed, but can't find the bracket and hall sensor... Time to tear apart the office... (dont have a garage).
Pictures of the goodies soon.
http://www.althafastener.com/Stainless- ... p_202.html
http://www.inlinetube.com/clips%20brake ... /clips.htm
http://www.mrostop.com/clips-c-543_1045_1047.html
Dale
"Fear The Government That Wants To Take Your Guns" - Thomas Jefferson
1970 "Kellison Sand Piper Roadster"
1970 "Kellison Sand Piper Roadster"
- kuleinc
- Posts: 193
- Joined: Tue Nov 25, 2008 3:35 pm
Re: My Megasquirt build, Stockish 1600
Certainly interested in your build did you get it running on MS yet?
1995 BMW 318ti with M3 Motor (Mine)
1994 BMW 325i Sedan (Hers)
1968 Baywindow Camper (Parts Bus)
1971 Westy Baywindow (EFI project...)
My build thread: viewtopic.php?f=14&t=137593
1994 BMW 325i Sedan (Hers)
1968 Baywindow Camper (Parts Bus)
1971 Westy Baywindow (EFI project...)
My build thread: viewtopic.php?f=14&t=137593
- volksbugly
- Posts: 634
- Joined: Thu Sep 16, 2010 5:09 am
Re: My Megasquirt build, Stockish 1600
https://picasaweb.google.com/1078300117 ... 6939243602
not running yet,
Wideband is in, toothed pully is in,
I am doing everything next week since I have a week off paid from work.
Taking over the living room, ya the wife wants to kill me:
https://picasaweb.google.com/1078300117 ... 6939243602
ah and for full sequential you need a cam sensor and a crank sensor, for the crank I did Mario's pully,
for the cam I did CB Cam Sync.. Its pretty heavy duty I thought it would be some plastic thing but its solid billet its probably about 3 to 5 lbs
CB CamSync:
https://picasaweb.google.com/1078300117 ... 6970977218
one negative - the screw heads were partially stripped
Check out the secret Santa gift that was given to me!
http://www.youtube.com/watch?v=jfGfgvZs ... OO8iJZwtKS
not running yet,
Wideband is in, toothed pully is in,
I am doing everything next week since I have a week off paid from work.
Taking over the living room, ya the wife wants to kill me:
https://picasaweb.google.com/1078300117 ... 6939243602
ah and for full sequential you need a cam sensor and a crank sensor, for the crank I did Mario's pully,
for the cam I did CB Cam Sync.. Its pretty heavy duty I thought it would be some plastic thing but its solid billet its probably about 3 to 5 lbs
CB CamSync:
https://picasaweb.google.com/1078300117 ... 6970977218
one negative - the screw heads were partially stripped
Check out the secret Santa gift that was given to me!
http://www.youtube.com/watch?v=jfGfgvZs ... OO8iJZwtKS
- volksbugly
- Posts: 634
- Joined: Thu Sep 16, 2010 5:09 am
Re: My Megasquirt build, Stockish 1600
Well I was lazy during the break, I got the left side throttle body installed, along with my fuel pressure gauge. It was a really tight fit. I had to use a hammer to dent out the sides because the fuel rail is hitting. I ended up having to make trips to the hardware store and VW shop, every time I did that it was 3 hours out of my day. Waking up at 11am didnt help either since it gets dark here at 5pm. The dark doesn't really bother me but by 6pm its cold.
Here are some pics: (If I do this right)
(Sorry I boogered my web album.) !!!
See page 3 or check out the album directly here
https://picasaweb.google.com/1078300117 ... directlink
Here are some pics: (If I do this right)
(Sorry I boogered my web album.) !!!
See page 3 or check out the album directly here
https://picasaweb.google.com/1078300117 ... directlink
Last edited by volksbugly on Fri Jul 20, 2012 8:44 pm, edited 2 times in total.