Page 1 of 2

unibody considerations with high power

Posted: Sun Dec 22, 2002 3:48 pm
by Mueller
neutral drops? Image

I never knew they built an automatic 915 transmission!?!?

unibody considerations with high power

Posted: Sun Dec 22, 2002 3:58 pm
by porsche_914_freak
who said anything about an automatic?

neutral drop is when your in gear, and slide your foot off the clutch petal sideways so the clutch "drops".

unibody considerations with high power

Posted: Sun Dec 22, 2002 5:25 pm
by Mueller
"Dumping the clutch" is what you mean...

"neutral drop" is when you have the car in neutral, rev the motor and slam the shifter into gear....only in an automatic
can this be done, which is a good way to ruin a tranny Image

why slide your foot sideways? just let go of the darn thing

what motor? you won't be doing any kind of burnouts with a /4 motor

unibody considerations with high power

Posted: Sun Dec 22, 2002 8:45 pm
by Mark the canuck
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Mueller:
<B>"Dumping the clutch" is what you mean...
</B><HR></BLOCKQUOTE>

Yep, you bought the wrong car dude!

914's are for the twisties not the 1/4

unibody considerations with high power

Posted: Sun Dec 22, 2002 11:58 pm
by porsche_914_freak
we hope to build a strong enough car that it wont mind neutral drops and alot of abuse. do we need to weld tube all around the engine/tranny mounts? how strong is the stock motor mounts anyways? the stock tranny is being replaced by a 915 gearbox and 930 cv joints. but i wonder if the tranny mounts wont rip holes right through the trunk? maybe steel plating?

unibody considerations with high power

Posted: Mon Dec 23, 2002 12:16 am
by shawn
the rubber engine mounts that hold the engine to the bar are not good for sudden jerks. i did a really good burn out in my 914 one day and tore both of those mounts in half and i only have a stock 1.8. so i would look at using something alot stronger.
shawn

unibody considerations with high power

Posted: Mon Dec 23, 2002 1:56 am
by porsche_914_freak
ok, clutch dumping it is. i used the wrong words.

how did we get the wrong car? isnt a car only what you make it to be?

unibody considerations with high power

Posted: Mon Dec 23, 2002 9:42 am
by Mueller
I know of a few 3.0 powered 914's running the 901 tranny's that'll dump the clutch to smoke the tires once in a while. no harm.

A lot of it depends on the tires and the motor. My 914 2.0 would spin the tires for about 6 feet, my 3.6 911 layed down 40+ feet of two fat black strips in our parking lot Image
(not good for tranny, but I "had" to show off for a co-worker, LOL)

Stock rubber mounts might not live with this abuse. When I dropped the motor in my last 914, my tranny mounts started to show signs of cracking from the abuse I gave the car.

unibody considerations with high power

Posted: Mon Dec 23, 2002 7:12 pm
by RANDERSKI
The 915 trans won't handle the abuse for sure. Have considered a bus (late model type 2) trans? It can handle almost anything you can throw at it.

Solid mounts can be fabbed for the 914...if noise isn't an issue and plating the shock towers should be seriously considered.

Unibody construction can be stiffened tremendously by adding a full roll cage that ties in the corners of the car and takes up a portion of the twisting that the motor produces.

I know of half a dozen guys running 3.2+ motors that have overcome many of your concerns. Good luck with your project.

unibody considerations with high power

Posted: Mon Dec 23, 2002 8:22 pm
by porsche_914_freak
why wont the 915 tranny handle it? i have been told it will hold 500hp.

i like the idea with the shock towers, and solid motor mounts. a full roll cage might be over my head though Image

what about the rear swing arm mounts?

unibody considerations with high power

Posted: Mon Dec 23, 2002 11:32 pm
by porsche_914_freak
ok so, stronger motor and tranny mounts it is!
what about the unibody? can it handle hundreds of hp and torque?

this is what we are scared of the most, seeing the motor and tranny fall to the ground in a twist of torque when the tires hook up with traction.

unibody considerations with high power

Posted: Mon Dec 23, 2002 11:44 pm
by Mueller
unless you have a monsterous V8 car with huge tires, I wouldn't worry about it too much....and even then, things can be taken care of...there will always be a weak link, just hope it's the cheapest thing to fix Image

unibody considerations with high power

Posted: Tue Dec 24, 2002 11:43 pm
by RANDERSKI
915 Trans is not very cost effective to R&D (Break parts)...if you have the bucks to drop on it go for it. Other wise you'll need to explore other cost effective options. What are your intentions with the car? Track or strip? Rear swing mounts should be ok...most guys will box the rear arms to make them more ridgid though. If you plan on running the car on the track or even on the street with BIG power go for the cage! It will save you some time down the road and possibly your life. Let me know if you decide to go with a cage...I am putting one in our shop's 914 in the next week.



------------------
Eurowerks Motorsports
KSRacecars = VW performance

unibody considerations with high power

Posted: Thu Dec 26, 2002 1:50 pm
by porsche_914_freak
our intentions for the car is track, strip and street. i know thts is a difficult thing to do. i figure if its fast on the track its fast on the street. and for the strip just deflate the rear tires a bit Image

basically, take a stock 914, make the rear portion stronger to hold more power, throw some fatty tires on it and install a j ported 13b 2 turbo intercooled rotary engine. then finish it off with suspension, brake and body upgrades.

weight will be the same as stock, only with 4-5 times more horsepower.

the engine is already done, tranny and front syspension of a 911 are sitting in the gurage.

all we really need help with is figuring out what exactly needs to be modified for more strength.

boxed trailing arms, welded up rear shock towers that have welded tubes going to plates of steel on the tranny mounts. solid motor mounts. rubber new tranny mounts. 930 cd joints.

we still need to send the tranny out to get the diff flipped.

what else could be done for more body strength?

why do you say the 915 tranny is no good? i thought it was able to handle more power and abuse?

unibody considerations with high power

Posted: Sun Dec 29, 2002 5:47 pm
by RacerBVD
I have a 914 roller that is already fully caged, and has tranny braces as well!! This could be a good start for you. Email me for pictures!!

------------------
RacerBVD
http://members.rennlist.com/racerbvd/