Mahle cylinder boring

VW based Porsche. In a league of its own.

Moderator: Piledriver

Post Reply
Bsherrard
Posts: 13
Joined: Mon Jul 24, 2017 5:54 pm

Mahle cylinder boring

Post by Bsherrard » Sat Sep 09, 2017 7:22 pm

Anyone know a shop that can bore my original German Mahle cylinders to 96mm?? Not having any luck finding a place.

User avatar
Piledriver
Moderator
Posts: 21720
Joined: Sat Feb 16, 2002 3:01 am
Location: Van Alstyne, Texas

Re: Mahle cylinder boring

Post by Piledriver » Sat Sep 09, 2017 9:21 pm

European Motor Works or RIMCO.
Getting them packaged right is most of the battle.

Be aware you are not saving money going down that path, the new EMW jugs are also not bad from all accounts.
The potential advantage is the heat cycled/aged jugs should stay round better, as well as wear better..

Also note most motorcycle shops can bore/hone free standing iron jugs, or know a machine shop that can.
I, for one, regularly embrace our new robot overlords, as I am the guy fixing the robots...

Bsherrard
Posts: 13
Joined: Mon Jul 24, 2017 5:54 pm

Re: Mahle cylinder boring

Post by Bsherrard » Sun Sep 10, 2017 7:19 am

Piledriver,
I will check with EMW and RIMCO. Thanks.
Good thought on the bike shops, didn't think of that.
Brook

Bsherrard
Posts: 13
Joined: Mon Jul 24, 2017 5:54 pm

Re: Mahle cylinder boring

Post by Bsherrard » Mon Oct 09, 2017 4:50 pm

Just a quick follow up. Neither EMW or RIMCO would do the cylinder boring. There is a local shop that does jet ski and motorcycles but they wouldn't do them either. Finally found a machine shop that will do them, they have done them in the past but it was a long time ago. They are going to have to fabricate a thrust plate to do the job. We will see how they turn out - might end up just going with the Chinese junk!
This is just crazy - I bet 20 years ago this was an everyday procedure!
Brook

User avatar
sideshow
Posts: 3206
Joined: Mon Oct 27, 2003 2:00 pm
Location: suth'ern oraygun yusa
Contact:

Re: Mahle cylinder boring

Post by sideshow » Mon Oct 09, 2017 9:09 pm

Wow, I kinda expected RIMCO to fall off the planet due to all the in-house skill lost over the last few moves.
I also thought this was still a common procedure especially in the bike crowd.

So I guess it is just a matter of hours before the only person on the planet that can afford to repair a car will be Jay Leno.
Yeah some may call it overkill, but you can't have too much overkill.

H2OSB
Posts: 455
Joined: Mon Aug 21, 2000 2:01 am

Re: Mahle cylinder boring

Post by H2OSB » Tue Oct 10, 2017 3:34 pm

I have a set of those cylinders and considered both boring the 94s to 96s, and finding workable 94s for the 66mm crank(T1Cs...i think that's what it is), but in the end with Pile's good advice and considering the fact I'm a cheap ass, I decided to hold off to get set of EMW 96 Ps&Cs. Glad I waited...I ended up acquiring a 71mm crank when my son gave up on his T4 dreams.

H2OSB

Bsherrard
Posts: 13
Joined: Mon Jul 24, 2017 5:54 pm

Re: Mahle cylinder boring

Post by Bsherrard » Tue Oct 10, 2017 3:38 pm

I may end up going that route if the boring doesn't work out. I really prefer to keep the German Mahle's - they are nice cylinders!
I guess I could always splurge on Nickies, I mean hey...their only $2,760!!
Brook

User avatar
raygreenwood
Posts: 11740
Joined: Wed Jan 22, 2003 3:01 am

Re: Mahle cylinder boring

Post by raygreenwood » Thu Oct 19, 2017 9:30 am

Call Roy at Mofoco. He may not be a type 4 full time mechanic.....but I will wager he has tools and experience including torque plates to hone cylinders.
Ray

Post Reply